Topographic signatures and manipulations of Fe atoms, CO molecules and NaCl islands on superconducting Pb(111)

• Carl Drechsel,
• Philipp D’Astolfo,
• Jung-Ching Liu,
• Thilo Glatzel,
• Rémy Pawlak and
• Ernst Meyer

Beilstein J. Nanotechnol. 2022, 13, 1–9, doi:10.3762/bjnano.13.1

• with functionalized tips. We report on the topographic signatures observed by scanning tunneling microscopy (STM) of carbon monoxide (CO) molecules, iron (Fe) atoms and sodium chloride (NaCl) islands deposited on superconducting Pb(111). For the CO adsorption a comparison with the Pb(110) substrate is

• of iron atoms on top of the prototypical Pb(111) superconducting surface. Keywords: carbon monoxide (CO); lateral manipulation; NaCl; scanning tunneling microscopy; superconductivity; Introduction The most exciting manifestation of topological superconductivity [1][2][3] is the Majorana zero mode

• systematic characterization by STM of the adsorption of carbon monoxide (CO), sodium chloride (NaCl) and iron adatoms (Fe) on the superconducting Pb(111) surface at low temperature (4.7 K). We show a surprising absence of STM topographic signatures of CO molecules on Pb(111), which we impute to their high

Determining amplitude and tilt of a lateral force microscopy sensor

• Oliver Gretz,
• Alfred J. Weymouth,
• Thomas Holzmann,
• Korbinian Pürckhauer and
• Franz J. Giessibl

Beilstein J. Nanotechnol. 2021, 12, 517–524, doi:10.3762/bjnano.12.42

• . Single iron adatoms were evaporated with a custom-built evaporator onto the cold sample. Carbon monoxide (CO) was leaked in at a partial pressure of 5 × 10−8 mbar for 5 min. Results and Discussion Determining A and θ with a 2D current map In the following, a method to determine A and θ is presented. As

The role of gold atom concentration in the formation of Cu–Au nanoparticles from the gas phase

• Yuri Ya. Gafner,
• Svetlana L. Gafner,
• Darya A. Ryzkova and
• Andrey V. Nomoev

Beilstein J. Nanotechnol. 2021, 12, 72–81, doi:10.3762/bjnano.12.6

• application in the field of catalysis and optics. Thus, it has been shown that, in heterogeneous catalysis, Cu–Au nanoalloys usually exhibit a synergistic effect in oxidative reactions and the preferential oxidation of carbon monoxide (CO) to carbon dioxide at ambient temperature as well as in the selective

Selective gas detection using Mn₃O₄/WO₃ composites as a sensing layer

• Yongjiao Sun,
• Zhichao Yu,
• Wenda Wang,
• Pengwei Li,
• Gang Li,
• Wendong Zhang,
• Lin Chen,
• Serge Zhuivkov and
• Jie Hu

Beilstein J. Nanotechnol. 2019, 10, 1423–1433, doi:10.3762/bjnano.10.140

• between the two metal oxides. The sensor based on the Mn3O4/WO3 composite with 3 atom % Mn showed a high selective response to hydrogen sulfide (H2S), ammonia (NH3) and carbon monoxide (CO) at working temperatures of 90 °C, 150 °C and 210 °C, respectively. The demonstrated superior selectivity opens the

Wet chemistry route for the decoration of carbon nanotubes with iron oxide nanoparticles for gas sensing

• Hussam M. Elnabawy,
• Juan Casanova-Chafer,
• Badawi Anis,
• Mostafa Fedawy,
• Mattia Scardamaglia,
• Carla Bittencourt,
• Ahmed S. G. Khalil,
• Eduard Llobet and
• Xavier Vilanova

Beilstein J. Nanotechnol. 2019, 10, 105–118, doi:10.3762/bjnano.10.10

• recovery in dry air. To determine the selectivity of the sensor for carbon monoxide (CO) and benzene (C6H6), gas cylinders with a 100 ppm CO and 10 ppm C6H6 concentrations respectively, balanced in dry air, were used with the previously described set-up. To create the desired humidity in order to check the

A review of carbon-based and non-carbon-based catalyst supports for the selective catalytic reduction of nitric oxide

• Shahreen Binti Izwan Anthonysamy,
• Syahidah Binti Afandi,
• Mehrnoush Khavarian and
• Abdul Rahman Bin Mohamed

Beilstein J. Nanotechnol. 2018, 9, 740–761, doi:10.3762/bjnano.9.68

• widely applied over several decades to meet the stringent regulation of NO emissions from stationary sources [4]. Meanwhile, the three-way catalyst with carbon monoxide (CO) and hydrocarbon is also used in mobile sources to remove NO from gasoline, but this technology is limited to diesel and lean-burn

Low-temperature CO oxidation over Cu/Pt co-doped ZrO₂ nanoparticles synthesized by solution combustion

• Amit Singhania and
• Shipra Mital Gupta

Beilstein J. Nanotechnol. 2017, 8, 1546–1552, doi:10.3762/bjnano.8.156

• .8.156 Abstract Zirconia (ZrO2) nanoparticles co-doped with Cu and Pt were applied as catalysts for carbon monoxide (CO) oxidation. These materials were prepared through solution combustion in order to obtain highly active and stable catalytic nanomaterials. This method allows Pt2+ and Cu2+ ions to

• gas hourly space velocity (GHSV) and initial CO concentration. Keywords: CO oxidation; copper; nanoparticles; platinum; solution combustion; zirconia; Introduction The catalytic oxidation of carbon monoxide (CO) is of potential interest in applications such as CO sensors, carbon dioxide (CO2) lasers

Metal oxide nanostructures: preparation, characterization and functional applications as chemical sensors

• Dario Zappa,
• Angela Bertuna,
• Elisabetta Comini,
• Navpreet Kaur,
• Nicola Poli,
• Veronica Sberveglieri and
• Giorgio Sberveglieri

Beilstein J. Nanotechnol. 2017, 8, 1205–1217, doi:10.3762/bjnano.8.122

• . Samples were finally mounted on TO39 packages using electro-soldered gold wires. A flow-meter technique was used to evaluate the performance of fabricated conductometric devices for the detection of two common air contaminants, namely carbon monoxide (CO) and nitrogen dioxide (NO2). Samples were mounted

Enhanced catalytic activity without the use of an external light source using microwave-synthesized CuO nanopetals

• Govinda Lakhotiya,
• Sonal Bajaj,
• Arpan Kumar Nayak,
• Debabrata Pradhan,
• Pradip Tekade and
• Abhimanyu Rana

Beilstein J. Nanotechnol. 2017, 8, 1167–1173, doi:10.3762/bjnano.8.118

• carbon monoxide (CO) [7][8][9]. CuO is one of the few p-type metal oxide semiconductors with a narrow band gap ≈1.24 eV [10]. The properties of CuO nanomaterials (nanoparticles, nanowires, nanosheets, etc.) are closely related to morphology and crystallite size [7]. These different nanoscale morphologies

Graphene functionalised by laser-ablated V₂O₅ for a highly sensitive NH₃ sensor

• Margus Kodu,
• Artjom Berholts,
• Tauno Kahro,
• Mati Kook,
• Peeter Ritslaid,
• Helina Seemen,
• Tea Avarmaa,
• Harry Alles and
• Raivo Jaaniso

Beilstein J. Nanotechnol. 2017, 8, 571–578, doi:10.3762/bjnano.8.61

• , respectively, which is indeed observed. The response to another common reducing gas, the air pollutant carbon monoxide (CO) was also tested. The inset in Figure 4 demonstrates the response of a V2O5 functionalised sensor to 100 ppm CO. Although the sensor is sensitive to CO and a ≈7% decrease in conductivity

Thin SnO_x films for surface plasmon resonance enhanced ellipsometric gas sensing (SPREE)

• Daniel Fischer,
• Andreas Hertwig,
• Uwe Beck,
• Volkmar Lohse,
• Detlef Negendank,
• Martin Kormunda and
• Norbert Esser

Beilstein J. Nanotechnol. 2017, 8, 522–529, doi:10.3762/bjnano.8.56

• several gas species in the surface plasmon resonance enhanced (SPREE) gas measurement. It was found that the undoped tin oxide (SnOx) shows higher sensitivities to propane (C3H8) then to carbon monoxide (CO). By using Fe:SnOx, this relation is inverted. This behavior was explained by a change of the

Nanocrystalline ZrO₂ and Pt-doped ZrO₂ catalysts for low-temperature CO oxidation

• Amit Singhania and
• Shipra Mital Gupta

Beilstein J. Nanotechnol. 2017, 8, 264–271, doi:10.3762/bjnano.8.29

• were performed in order to characterize the catalyst. The calculated crystallite size of ZrO2, calculated with the help of the Scherrer equation, was around 30.3 nm. The synthesized ZrO2 was scrutinized regarding its role as catalyst in the oxidation of carbon monoxide (CO). It showed 100% CO

• refractory metal [6], in thermal barrier coating [7], gas sensors [8], in solid oxide fuel cells [9], in ceramic production, insulation and abrasives. Carbon monoxide (CO) is considered a major pollutant and it causes serious health problems. It is important to control CO released from natural sources and

Sensitive detection of hydrocarbon gases using electrochemically Pd-modified ZnO chemiresistors

• Elena Dilonardo,
• Michele Penza,
• Marco Alvisi,
• Gennaro Cassano,
• Cinzia Di Franco,
• Francesco Palmisano,
• Luisa Torsi and
• Nicola Cioffi

Beilstein J. Nanotechnol. 2017, 8, 82–90, doi:10.3762/bjnano.8.9

• such as carbon monoxide (CO) and hydrocarbons (HCs) [26]. The magnitude of the variation of the electrical resistance gives a direct measure of the concentration of the analyte gas [25]. In the last decades, different nanostructured MOx-based gas sensors with improved performance in the HC gas

Nanostructured SnO₂–ZnO composite gas sensors for selective detection of carbon monoxide

• Paul Chesler,
• Cristian Hornoiu,
• Susana Mihaiu,
• Cristina Vladut,
• Jose Maria Calderon Moreno,
• Mihai Anastasescu,
• Carmen Moldovan,
• Bogdan Firtat,
• Costin Brasoveanu,
• George Muscalu,
• Ion Stan and
• Mariuca Gartner

Beilstein J. Nanotechnol. 2016, 7, 2045–2056, doi:10.3762/bjnano.7.195

• an ecologically friendly preparation technique. Carbon monoxide (CO) is one of the most dangerous gases present in our surrounding environment. As it does not have a specific smell, color or taste, CO detection is impossible without special warning systems [24]. When organic matter is oxidized the

Materials and characterization techniques for high-temperature polymer electrolyte membrane fuel cells

• Roswitha Zeis

Beilstein J. Nanotechnol. 2015, 6, 68–83, doi:10.3762/bjnano.6.8

• clean hydrogen sources and a sizable hydrogen infrastructure limits the fuel-cell applications today. Due to their elevated operating temperatures, between 150 and 180 °C, HT-PEMFCs can tolerate fuel contaminants such as carbon monoxide (CO) and hydrogen sulfide (H2S) without significant loss of

Effects of palladium on the optical and hydrogen sensing characteristics of Pd-doped ZnO nanoparticles

• Anh-Thu Thi Do,
• Hong Thai Giang,
• Thu Thi Do,
• Ngan Quang Pham and
• Giang Truong Ho

Beilstein J. Nanotechnol. 2014, 5, 1261–1267, doi:10.3762/bjnano.5.140

• sensitivity of the ZnO– 0.5 wt % Pd sensor depends on the operating temperature. This is shown in Figure 5 for 1 vol % of hydrogen, H2, carbon monoxide, CO, and for propane, C3H8. The comparison of the specificity of the sensor for the studied gases at 250 °C shows that the sensor is highly sensitive to H2

Design criteria for stable Pt/C fuel cell catalysts

• Josef C. Meier,
• Carolina Galeano,
• Ioannis Katsounaros,
• Jonathon Witte,
• Hans J. Bongard,
• Angel A. Topalov,
• Claudio Baldizzone,
• Stefano Mezzavilla,
• Ferdi Schüth and
• Karl J. J. Mayrhofer

Beilstein J. Nanotechnol. 2014, 5, 44–67, doi:10.3762/bjnano.5.5